Sold by the 5 meter reel, foot and sample kit. Ultraviolet 400nm LED strip, also known as near ultraviolet, Ultraviolet A (400-315nm) long wave, or black light LED strip, should be used only when UVA light is required.
When illuminated UV 400nm LED strip light will emit some visible violet light. However, do not judge the brightness of this strip with your eye, as a large portion of the light output from the 400nm UV strip is invisible to the human eye.
This UVA light is useful for observing fluorescence and can be used for a multitude of purposes such as artistic black lighting effects, detection of counterfeit money, security, curing plastic resins, therapeutic and diagnostic medicinal uses, and attracting insects. Tight spectral power distribution, centered on 400 nm. UVB (315-280nm) and UVC (280-100nm) light serve different applications, such as germicidal disinfection and extreme ultraviolet lithography.
The Current Control LED strip light series from EnvironmentalLights is the pinnacle of LED strip quality. Each segment has individual current control to ensure the LEDs get the current they need, no matter where they are on the strip. This ensures that the lights are just as bright at 21 volts as 24 volts, and it provides uniform brightness along the strip, and uniform color for RGB and RGA strips. This allows you to run up to 6 meters of single row 5050 (50mm x 50mm) LEDs or 5 meters of double row LEDs. Although the extra Current Control circuitry costs a bit more, you might save more than that in labor and wiring costs. The pros have been asking us for this, and it's already selling very well. Available in a host of colors, RGB, RGA and waterproof versions, as well.
Current Control strip works with standard PWM dimmers and controllers and voltage varying dimming units we sell. As indicated earlier, dimming range when using voltage varying will not begin until voltage drops to 21 volts, so there is a range shift, versus traditional resistor-only strip. For that reason, we do not recommend dimming Current Control using supplies that operate by reducing voltage to reduce current.
Easy to install:
- Non-waterproof version has high-adhesion stickyback. Just peel off the wax paper and stick it to any clean, dry substrate.
- Waterproof version comes with 20 rubber tie downs if you buy the complete reel, plus a glue tube, plus 4 caps for the ends. You get those accessories with full-reel purchases only. Or you can buy the special foam tape and glue we list as companion parts.
Easy to control using any of our LED controllers or dimmers. Or use any DMX controller, in conjunction with our DMX-4-5000 or DMX-24-2000S decoders.
- Black Light UV 400 nm (400 nm wavelength.)
- Not waterproof. Available in waterproof and non-waterproof.
- 4145 mW/meter = 16 lumens/meter.
- 24 volts DC.
- 100 watts (6.1 watts/foot = 20 watts/meter.)
- Length: 16.4 ft = 5 m.
- Width: 0.79 in = 20 mm.
- Height: 0.09 in = 2.2 mm.
- LED spacing: 0.66 in = 16.7 mm.
- Cuttable in segments of 3 LED nodes. Cutting increment: 1.97 in = 50 mm.
- UL, RoHS.
- 50,000 hours expected lifetime.
- Warranty: 3 years limited.
- Easy-to-use ribbon to cable connectors, ribbon to ribbon connectors and ribbon to ribbon jumpers are available for the single row version, but not the double row version, because it uses a lot of current. Wires are soldered on both ends of the strip for your convenience.
- No Ultra-Violet emissions (except for the special UV version), so it won't harm your art or documents.
- We use high quality LEDs for maximum color vibrancy, longevity and a well-balanced 'all-on' white. We pay more for our LED components, and you'll benefit from the difference. This is not a commodity product. Quality matters, and the materials, controls, connections and tech support we provide will make your project successful.
- Cut LED strip lighting is not returnable.
- We provide detailed installation instructions, design criteria and technical support upon request.
- Can be used with the channel or light bars listed on the Companion Parts tab.